共找到 96 條與 鐵路信號綜合 相關的標準,共 7 頁
Rail Transit Municipal Railway and Urban Rail Transit Management and Command/Control Systems Part 2: Functional Requirements Specification
Rail Transit Municipal Railway and Urban Rail Transit Management and Command/Control Systems Part 3: System Requirements Specification
Rail Transit Municipal Railway and Urban Rail Transit Management and Command/Control Systems Part 1: System Principles and Basic Concepts
Railroad Signaling Glossary Part 1: Railroad Signaling Glossary
Railway signal light luminous intensity
本標準規定了鐵路信號電子設備對雷電電磁脈沖誘發的過電壓和過電流安全防護的基本原則和防護技術要求,不考慮鐵路信號設備所處場地建筑物對直接雷擊的防護。
Technical specification for protection against lightning electromagnetic impulse on railway signaling equipments
Railway applications - Communication, signalling and processing systems - European Rail Traffic Management System - Driver-Machine Interface - Part 2: Ergonomic arrangements of GSM-R information; German version CLC/TS 50459-2:2015
Railway applications - Communication, signalling and processing systems - European Rail Traffic Management System - Driver-Machine Interface - Part 1: General principles for the presentation of ERTMS/ETCS/GSM-R information; German version CLC/TS 50459-1:2
Railway applications - Communication, signalling and processing systems - European Rail Traffic Management System - Driver-Machine Interface - Part 3: Ergonomic arrangements of non ETCS information; German version CLC/TS 50459-3:2016
本標準規定了鐵路信號燈光顏色的色品區域范圍和測試方法。 本標準適用于鐵路信號燈光顏色的紅色、黃色、綠色、藍色、紫色及白色(月白色)。
Colours of railway signal light
本標準規定了鐵路地面信號產品(以下簡稱產品)高溫及低溫的試驗種類、試驗條件的劃分、試驗溫度及試驗方法等。 本標準適用于考核鐵路地面信號產品在規定的溫度環境條件下進行高溫及低溫適應性的試驗方法。 本標準不適用于以下幾種情況: a)以研究產品隨溫度周期變化而變化為目的的試驗; b)以研究產品耐久性,耐候性及耐腐蝕性為目的的試驗; c)在運輸及儲存條件下,以研究產品受到溫度影響而變化為目的的試驗; d)安裝在機車車輛上的設備及部件受到溫度變化影響的試驗。
High and low temperature testing methods for parts of railway signaling
本標準規定了軌道電路的技術要求,是軌道電路研究、設計和制造的技術準則。 本標準適用于鐵路區間及站內的軌道電路。
Track circuit general technical specifications
本標準規定了鐵路信號電工和電氣電子類產品的絕緣電阻以及相關的試驗方法。 本標準適用于鐵路信號產品。
Insulation resistance of railway signal product
本標準規定了鐵路地面信號產品(以下簡稱產品)在振動臺上進行一般振動試驗(以下稱振動試驗)的方法。 本標準適用于鐵路地面信號產品。
Vibration testing methods for products of railway signaling on earth
This European Standard defines the minimum performance requirements of on-board monitoring systems for axlebox condition monitoring by means of temperature measurements. This European Standard refers to temperature monitoring of the axlebox.However,the design may be such that the rolling bearing itself is monitored directly.
Railway applications.Axlebox condition monitoring.Interface and design requirements.Part 2: Performance and design requirements of on-board systems for temperature monitoring; German version EN 15437-2:2012
This British Standard specifies the symbols to be used on railway signalling plans but does not provide guidance on their application.
Railway signalling symbols. Specification for schematic symbols
This part of IEC 61375 specifies the data communication bus inside consists that are based on CANopen. CANopen was developed for use in, but is not limited to, industrial automation applications. These applications may include devices such as input/output modules, motion controllers, human machine interfaces, sensors, closed-loop controllers, encoders, hydraulic valves or programmable controllers. In the application field of rail vehicles CANopen networks are utilized to network subsystems in consists such as e.g. brake control system, diesel engine control system and interior or exterior lighting control system. In addition CANopen is utilized as consist network to enable the data exchange between the different subsystems within one single rail vehicle or a group of rail vehicles sharing the same Consist Network. This part of IEC 61375 applies to all equipment and devices operated on a CANopen-based consist network within TCN architecture as described in IEC 61375-1. The applicability of this standard to a TCN implementation allows for individual conformance checking of the implementation itself and is a pre-requisite for further interoperability checking between different TCN implementations. In any case, proof of compatibility between Train Backbone and the Consist Network will have to be brought by the supplier. This part of IEC 61375 applies to the architecture of communication systems in Open trains. In addition it may be applicable to closed trains and multiple unit trains when so agreed between purchaser and supplier.
Electronic railway equipment - Train Communication Network (TCN) - Part 3-3: CANopen Consist Network (CCN)
This part of IEC 61375 applies where MVB is required.
Electronic railway equipment - Train Communication Network (TCN) - Part 3-1: Multifunction Vehicle Bus (MVB)
IEEE Standard for the Functioning of Interfaces Among Propulsion, Friction Brake, and Train-Borne Master Control on Rail Rapid Transit Vehicles
本標準規定了計軸設備的組成、工作環境、技術要求、試驗方法、檢驗規則和標志、包裝、運輸、貯存。 本標準適用于計軸設備的設計、制造、檢驗和維修。
General technical specification for railway axle counters
Copyright ?2007-2025 ANTPEDIA, All Rights Reserved
京ICP備07018254號 京公網安備1101085018 電信與信息服務業務經營許可證:京ICP證110310號
頁面更新時間: 2025-02-05 23:51